Hw-module Slot R1 Reload

Can anyone comment on RSP redundancy with SSO mode?

To power off a particular module, use Switch(config)# no hw-module module num power; you can find that command on Page 20 of this Cisco doc. FYI, there isn't a graceful shutdown command for the whole switch. You should backup your config (just in case), issue a reboot, wait till you can audibly hear a change in fan speed, and then remove. The hw-module subslot reload command reloads Cisco IOS XR software on the specified SPA and restarts the SPA interfaces. The SPA reloads with the current running configuration and active software set for the SPA.

I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE

Hw-module Slot R1 Reloadable

Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
what might be wrong here?
_______________________________________________

Hw-module Slot R1 Reloader

cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/

Hw-module Slot R1 Reloading

This is the default MODPACK that occupies the F SLOT. All adjustable MODS can be adjusted in MOD Central. This section provides information on adjusting them on your controller using the MODPACK MOD Menu. To enter the MODPACK MOD Menu, HOLD for at least 5 seconds. You MUST remain HOLDING to stay in MOD Menu: MODPACK MOD MenuNavigation: or navigates FORWARD a CLASS LED. or navigates BACKWARD a CLASS LED. LED NUMBER 1-8 indicate the currently selected CLASS number. or navigates UP a MOD within the currently selected CLASS. or navigates DOWN a MOD within the currently selected CLASS. This will change your currently ENABLED MOD! ORANGE LIGHTBAR FLASHES (PS4) / LEFT TRIGGER RUMBLES (XB1) indicate the currently ENABLED MOD number. TOUCHPAD / MENU resets a CLASS to OFF (MOD 0). You MUST be selected on the correct MOD to adjust it. A single adjustable may be (Shared) by several MODS. ADJUSTABLE MODPACK: Number of Orange Flashes (PS4) / LT Rumbles (XB1) You MUST be selected on the correct MOD to adjust it A single adjustable may be (Shared) by several MODS 1. Primary Weapon Fire 2: Rapid Fire Adjustable 4: Burst Fire Adjustable Speed: L1 / LB Decrease R1 / RB Increase R2 / RT Test Burst Fire - Bundle Value (Shared): L1 / LB Decrease R1 / RB Increase Bundle 1: MR6, L-CAR9, KUDA, VMP, WEEVIL, RAZORBACK, KN-44, HVK-30, ICR-1, DINGO Bundle 2: VESPER Bundle 3: MAN-O-WAR, BRM Bundle 4: SHEIVA, HAYMAKER 12, GORGON, DRAKON Bundle 5: 205 BRECCI Bundle Value setting is NOT saved Bullet Count: L2 / LT Decrease R2 / RT Increase 2: Scope Enable 4: Always On Inverted Y 6: Scope Disable Inverted Y Test button will move based on Button Layout! The following adjustables DO NOT apply to Weapon Optimizer: Anti-Recoil - L2 / LT & R2 / RT or R2 / RT Test Higher recoil requires heavier weight Too much weight and your weapon will point at the floor 4. Quick Scope 2: Press Sensitive Adjustable Timing: L1 / LB Slower R1 / RB Faster L2 / LT Test 5. Auto Run 2: Press Sensitive / Call of Duty Reload to Auto Run Delay: L1 / LB Decrease R1 / RB Increase (2 or 3 seconds is fine for most weapons, unless Auto Run is cancelling reloads) 7. Left Paddle / AB #1 2: Pulse Fire Adjustable 4: Rapid Fire Drop Shot 6: Easy Double Jump Speed: L1 / LB Decrease R1 / RB Increase Turbo 2.0 Right -